Update 2011/09 : To update other members in a running stack once you have prepared the master, you must copy and enable the image on each of them as follows : Switch#copy flash1:/c3750-advipservicesk9-mz.122-35. SE5flash2: Destination filename [c3750-advipservicesk9-mz.122-35.

Sex chat without registration payment - Updating boot path

If you want to manage switches or clusters of switches through a web interface (HTML), this is the only file you need to download. First of all, define the username/password of the FTP server (required for downloading the tar file from the ftp server): Ciscozine#archive download-sw /leave-old-sw ftp://192.168.1.123/Ciscozine/c2960s-universalk9-mz.150-2. SE5!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! [OK - 19046400/4096 bytes] Loading Ciscozine/c2960s-universalk9-tar.150-2. SE5!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! SE3 Old image will be left alone c2960s-universalk9-mz.150-2. If you want to use only the CLI to manage the switch, this is the only file you need to download. May 22 : %IMAGEMGR-6-AUTO_COPY_SW: Software was not copied May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW_INITIATED: Auto-advise-software process initiated for switch number(s) 1 May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: Systems with incompatible software May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: have been added to the stack.

SE5/ (directory) extracting c2960s-universalk9-mz.150-2. The May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: software running on all of the stack May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: members has been scanned, and it has May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: been determined that the stack can be May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: repaired by issuing the following May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: command(s): May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: archive copy-sw /force-reload /overwrite /dest 2 1 May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: Note that this operation May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: will temporarily interrupt May 22 : %IMAGEMGR-6-AUTO_ADVISE_SW: network operation.

SE5/ (directory) extracting c2960s-universalk9-mz.150-2. The new code revision should come up and start to run as expected on all the switches in the stack. In this case, two are the switches so the commands are: 5. Remember: If you don’t upgrade the IOS on every switch, you will have a version mismatch!

Now comes the trivial yet tricky part : How to activate the image.

A quick look at the boot vars show which image will be used.

Here we see that it’s still the original one : Switch#show boot BOOT path-list : flash:/c3750-ipbase-mz.122-35. SE5Config file : flash:/Private Config file : flash:/Enable Break : no Manual Boot : no HELPER path-list : Auto upgrade : yes Auto upgrade path : command to select which image to boot, even a Cisco Wiki page for the 3750 (which I suspect was wrong about this). The proper command is this one, run in Switch#show boot BOOT path-list : flash:/c3750-advipservicesk9-mz.122-35.

SE5Config file : flash:/Private Config file : flash:/Enable Break : no Manual Boot : no HELPER path-list : Auto upgrade : yes Auto upgrade path : , but you can also just leave it, as the switch will automatically boot the first image it finds alphabetically if the ones from the boot path-list aren’t found. CCCCCCCCCCCCCCCC[...] Switch#configure terminal Switch(config)#boot system switch all flash:/c3750-advipservicesk9-mz.122-35.

These paths will supply the content that will be on the classpath of the initial Fileset, and the files contained will marked with roles +INPUT,+OUTPUT and so be emitted as final artifacts. These paths will supply the content that will be on the classpath of the initial Fileset, and the files contained will be marked with roles +INPUT,-OUTPUT, so they may be used to generate output but will not themselves be emitted as final artifacts.

Set the debouncing interval (milliseconds) for syncing files from project directories into the boot-managed temporary directories in the fileset. Increasing this may help when there are many files and other processes are editing them in parallel.

I just wasted hours trying to figure out how to upgrade a Cisco Catalyst 3750 using the image instead of the archive, since I don’t want any fancy web interface on any of my core network devices.

All of the current documentation explains only how to use the Once the copy is over, the file is on the flash filesystem.